Effect of ultrasonic irradiation on structure and electrochemical properties of LiMn2O4 thin films cathode material for Li-ion micro-batteries

Two kinds of spinel LiMn₂O₄ thin film for lithium ion micro-batteries were successfully prepared on polycrystal Pt substrates by spin coating methods, which were carried out under ultrasonic irradiation (USG) and magnetic stirring (MSG), respectively. The microstructures and electrochemical performance of LiMn₂O₄ thin films were characterized by thermogravimetry analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), and galvanostatic charge-discharge measurements. It was found that the crystalline structure of USG samples grew better than that of the MSG samples. At the same time, higher discharge capacity and better cycle stability were obtained for the LiMn₂O₄ thin films of USG at the current density of 50 μAh/cm² between 3.0 and 4.3 V. The 1st discharge capacity was 57.8 μAh/cm²-μm for USG thin films and 51.7 μAh/cm²-μm for MSG thin films. After 50 cycles, 91.4% and 69% of discharge capacity could be retained respectively, indicating that ultrasonic irradiation condition during spin coating was more suitable for preparing spinel LiMn₂O₄ thin films with better electrode performance for lithium ion micro-batteries.     

Studies on nano suspensions of silver sol and redispersed nanocrystallite silver in aqueous and alcoholic media

Nanocrystallite silver and silver sol were prepared and characterized by UV-visible spectra, XRD, TEM and HRTEM. The crystallite silver is re-dispersed in two different media, namely, water and alcohol and sonicated before ultrasonic investigation. The silver sol was used as such. Three different models for the propagation of ultrasound through two phase media are compared in these three different types of nano suspensions. Effect of particle size and medium on ultrasonic velocity (U), compressibility (κ) impedance (Z) and viscous relaxation time (τ) is studied. The particle concentration range was 0.2-1 v/v. Density and viscosity of the dispersion and sol are measured at different particle volume fractions. Effective density and ultrasonic velocity are computed by Urick, Kuster and Toksöz and Urick and Ament models and compared with experimental velocities. Values of effective density obtained by using Urick and Urick and Ament equations closely agree with experimental results of density while Urick's equation prediction of velocity is in close agreement with the experimental velocities. This comes as a surprise in view of the large density difference between the medium and suspended particle and suggests the possibility of the balancing effect of the inertial and viscous forces operating in the suspension.     

超声喷雾热解法制备SnS薄膜的物性研究

用超声喷雾热解法制备SnS多晶薄膜,对比了三种不同前驱液配比浓度对SnS薄膜性能的影响。XRD测试表明,当前驱液为硫脲(0.5 mol·L-1)+四氯化锡(0.5 mol·L-1)+去离子水时,SnO2的衍射峰强度比较大;当前驱液为硫脲(0.6 mol·L-1)+四氯化锡(0.5 mol·L-1)+去离子水时,SnS的衍射峰占主要地位,其中也含有一定量的SnO2;当前驱液为硫脲(0.7 mol·L-1)+四氯化锡(0.5 mol·L-1)+去离子水时,退火后的薄膜为单一的SnS薄膜,具有斜方晶系结构。SEM观测发现,薄膜均匀、致密,前驱液中硫脲浓度较大时,颗粒也较大。透过谱测试表明,浓度对薄膜透过率影响较小。结合器件的暗I-V和C-V测试,用三种前驱液配比浓度所制备的器件的结特性差异不大;当前驱液中硫脲浓度较大时,载流子浓度相对较大。     

The effect of solute on ultrasonic grain refinement of magnesium alloys

An experimental study has been conducted to assess the structural refinement of magnesium and its alloys by ultrasonic irradiation during solidification. It is shown that (i) ultrasonic irradiation leads to significant refinement only in the presence of adequate solute, which is alloy dependent; (ii) the attendant grain density increases linearly with increase in solute content at a given irradiation level; (iii) increasing the solute content at a low irradiation level above the cavitation threshold is more effective than substantially increasing the irradiation intensity; and (iv) the difference in the grain size between two ultrasonicated magnesium alloys is mainly determined by the solute content rather than the irradiation intensity. In view of these, the effect of ultrasonic irradiation on solute redistribution in a solidifying magnesium alloy seems rather limited even at a substantial intensity level such as 1700 W cm⁻². The implications of these findings are discussed and a mechanism is proposed to account for the experimental observations.     

Determination of three-dimensional solubility parameters of chlorinated polypropylene by ultrasonic degradation

The degradation reactions of chlorinated polypropylene (CPP) in toluene under ultrasonic irradiation were studied. The Mark–Houwink equation acquired from fractional precipitations was also suitable for estimating the molecular weight of degraded CPP. An objective standard was proposed for judging the solution behaviour of CPP in solvents by the study on the relative solubility of CPP before and after degradation. Then Hansen three-dimensional solubility parameters and the total parameter of CPP were obtained by optimization calculation in terms of the criterion proposed here. It was proved that the total parameter of CPP is creditable by the turbidity method. Compared to other standards, the result obtained from the proposed standard accorded well with the standard of complete miscibility suggested by Flory–Huggins for polymers and solvents as well as the objective reality. This standard may provide a reference for other polymers.     

Analysis of benzophenone and 4-methylbenzophenone in breakfast cereals using ultrasonic extraction in combination with gas chromatography-tandem mass spectrometry (GC-MS)

Benzophenone (BP) and 4-methylbenzophenone (4MBP) are photo-initiators that are generally used to cure ink on carton boards.In this contribution, a fast and reliable method for the determination of BP and 4MBP in breakfast cereals is described. The sample was extracted ultrasonically using a mixture of dichloromethane and acetonitrile (1:1), followed by a clean-up of the extract using solid phase extraction with a silica cartridge. Finally, the extract was analysed by GC-MSⁿ. Benzophenone-d₁₀ was used as internal standard. The presented method is validated in terms of linearity, recovery, repeatability and intra-laboratory reproducibility, specificity, limit of detection and limit of quantification. In conclusion, this method is able to detect both BP and 4MBP at very low concentrations (LOD = 2 μg kg⁻¹) in breakfast cereals.     

Determination of thermal wave reflection coefficient to better estimate defect depth using pulsed thermography

Thermography is a promising method for detecting subsurface defects, but accurate measurement of defect depth is still a big challenge because thermographic signals are typically corrupted by imaging noise and affected by 3D heat conduction. Existing methods based on numerical models are susceptible to signal noise and methods based on analytical models require rigorous assumptions that usually cannot be satisfied in practical applications. This paper presents a new method to improve the measurement accuracy of subsurface defect depth through determining the thermal wave reflection coefficient directly from observed data that is usually assumed to be pre-known. This target is achieved through introducing a new heat transfer model that includes multiple physical parameters to better describe the observed thermal behaviour in pulsed thermographic inspection. Numerical simulations are used to evaluate the performance of the proposed method against four selected state-of-the-art methods. Results show that the accuracy of depth measurement has been improved up to 10% when noise level is high and thermal wave reflection coefficients is low. The feasibility of the proposed method in real data is also validated through a case study on characterising flat-bottom holes in carbon fibre reinforced polymer (CFRP) laminates which has a wide application in various sectors of industry.     

Scattering of plane acoustic waves by a transversely isotropic cylindrical shell—application to material characterization

Scattering of obliquely incident plane acoustic wave by an air-filled, transversely isotropic cylindrical shell immersed in water is investigated theoretically and experimentally. The normal mode expansion technique is employed for analyzing the scattering field, and then resonance modes of the shell appearing in modal scattering form functions are identified performing the resonance scattering analysis. Dispersion curves for Sholte-Stoneley, SH and Lamb waves are obtained and their characteristics are interpreted. Calculated backscattering and resonance spectra as well as dispersion curves are compared with those from ultrasonic experiments for two composite samples having the same nominal composition but fabricated under different conditions. Sensitive change of the dispersion curves is observed for both normal and oblique incidences, which demonstrates the feasibility of systematic inverse evaluation of damage or elastic constants of the composite shell using data from the acoustic scattering measurements.     

高速超声加工工具的研究与应用

本文将提供一种设计高速超声加工工具的新方法，并给出了高速超声加工工具的试验结果。     

Ultrasonic spectrum characterization of pig''''s pathological liver tissues

I.IntroductionCurrent1ythemajorityofcommcrcialultrasonicscannersutilizeon1ytheamplitudcinformationcarriedbytheechoesbackscatteredfrombiologicaltissuestoproduccandriageintimedomain.Potentia1lyusefulinformationinfrequencyd0maincontainedbytheechoesiscomp1ete1ydiscarded.Theu1trasonicspectrumanalysistechnique,whichcancompensatethislack,canpresentsomeusefulparametcrsinfrcqucncydomainusedinultrasonictissuecharacterization.Onthisbackgroud,asericsofworksonthisficldhavcbeendoneduringthepastdecadell-5l.…